Gaming Screen, Blog
Why Does Monitor Keep Going Black? 3 Superb Ways To Fix If It Happen
Why Does Monitor Keep Going Black For A Second?
So, why does monitor keep going black for a second? The primary reason your display goes black for a few seconds is that the wires connecting it to your computer are damaged. This is frequently the case if your monitor stays dark for a brief period of time and then comes back on. In this blog, we also have an article about choosing the best gaming monitors that you might want to see about it.
Monitors usually have lower input lag, higher refresh rates and faster response times than TVs, which make them a better choice for gaming.”
How To Fix Black Screen That Usually Happen In Windows 10
When a black screen arises, there are several factors to examine, including hardware or software issues. The techniques outlined here will walk you through troubleshooting and resolving the most frequent difficulties in Windows 10.
This behavior is reported to occur repetitively for as low is every second to every few minutes. What makes the issue worse is the fact that the monitor malfunctions without any specific event or time.”
Kevin Arrows, author from appuals.com
Examine possible connectivity problems
If the issue occurs prior to logging into Windows 10, there is most likely a problem with the device’s connection to the display. In this situation, you should verify the physical connection, verifying that both ends of the video signal cable are connected correctly to the appropriate in and out ports. Disconnecting and reconnecting the video cable, as well as shaking the mouse, might assist in reactivating the display.
Although it may seem obvious, double-check that the display is receiving electricity. If your video card supports several outputs, try using a different port and shaking the mouse or pressing any key on the keyboard to bring the monitor to life. While it is uncommon, a driver upgrade may occasionally redirect the video signal to a new port (DisplayPort, HDMI, DVI, Thunderbolt, VGA).
If your computer has both a discrete and an integrated graphics card, you can switch to the integrated video card to see if the discrete card is the issue. If you recently upgraded the UEFI (Unified Extensible Firmware Interface) or BIOS (basic input/output system), this may deactivate the discrete graphics card, which may be reactivated only through the motherboard settings.
When connected to an external display, you may enter the device’s control panel and adjust the brightness to eliminate the black screen. Additionally, it’s a good idea to verify that the monitor is connected to the right input. (If you are unsure how to access your monitor’s settings, you may need to see the manufacturer’s help page).
If the issue occurs on a laptop, boost the display brightness using the keyboard key combination. Typically, you’ll need to hit the Function (Fn) key in conjunction with one of the function keys, such as F8 or F10. Additionally, you may try connecting the monitor to a different computer or use a different video signal line to see whether the issue is with the display, graphics card, or cable.
Display detection
Occasionally, a black screen occurs when Windows 10 loses connectivity to the display. The Windows key + Ctrl + Shift + B keyboard shortcut may be used to restart the video driver and reconnect the monitor to the computer. On certain devices (such as the Surface Pro 7), you may wake up the screen by rapidly pushing the volume up and down keys three times.
When you do the wake action, a beep and activity on the screen indicate that Windows 10 is capable of responding to the command and is attempting to create a new connection. Alternatively, given that Windows 10 is responsive, you may enter the “Project” flyout menu by using the Windows key + P keyboard shortcut.
Then press the P key and Enter to cycle through the various display modes and check to see if the black screen vanishes. (Repeat the procedures four times to cycle through all potential modes.)
If the screen remains black, press and hold the power button for about ten seconds to power down the device. Then, to restart, hit the power button one more. (If you had documents open, this step may result in the loss of unsaved material).
Disconnect any gadgets that are not necessary
Peripherals attached to the device may cause the black screen or black screen with spinning dots to appear during startup. Typically, spinning dots on startup signify that an update is being installed and that you should wait a few moments, but if it takes an extended period of time, it might be a hardware compatibility issue.
If you have a similar issue, detach all accessories from your computer, including printers, cameras, removable disks, Bluetooth, docking station, and other USB devices. Restart the device, and if it resumes regular operation, the issue is most likely with one of the peripherals. You may establish which component is causing the disagreement by reconnecting them one at a time until you locate the culprit. Once you’ve identified the peripheral that’s causing the problem, detach it, restart the computer, conduct an internet search for a resolution, or contact the manufacturer for assistance.
Was this helpful?
I’m Roselyn T., a self-proclaimed tech geek on a mission to unravel the wonders of the digital realm. As a dedicated reviewer of computers and laptops, I share my insights and expertise on the latest tech trends and innovations on my blog, workrift.com. With a passion for demystifying the tech landscape, I not only offer in-depth reviews but also provide practical tips to navigate the ever-evolving world of technology. I’m also an author of the book “AP Computer Science A Premium, 2024: 6 Practice Tests + Comprehensive Review + Online Practice (Barron’s AP)” which is sold on Amazon. Join me as we explore the exciting intersection of form and function in the realm of gadgets and gear.